wiring diagram SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
vol.1
RELATED MANUAL
MANUAL NAMEMANUAL NO.APPLICABILITY
SQ416 / SQ420 / SQ625
Unit Repair Manual99501-65D01-xxxTransmission, Transfer and Differentials
(Front and Rear) of SQ series.
SQ416 / SQ420 / SQ625
Wiring Diagram Manual99512-65D10-015Applicable model mentioned in FOREWORD
of this manual.
SQ416 / SQ420 / SQ625
Service Manual99500-65D00-xxxVehicles before the vehicle identification number
mentioned in FOREWORD of this manual.
SQ416 / SQ420 / SQ625
Wiring Diagram Manual99512-65D01-015

YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-35
DIAGNOSTIC FLOW TABLE B-1 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªO / D OFFº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-20
(G16 / J20 engines) or E61-7 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªO / D OFFº light turn ON at ignition
switch ON?Poor E61-20 (G16 / J20
engines) or E61-7 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªW / Bº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-36 AUTOMATIC TRANSMISSION (4 A / T)
Switch ON
positionSwitch OFF
positionSwitch ON
position
Switch OFF
position
DIAGNOSTIC FLOW TABLE B-2 ªO / D OFFº LIGHT CIRCUIT CHECK
(ªO / D OFFº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-1 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check O / D cut Switch Position.
Is O / D cut switch turned OFF (Is switch button at OFF
position)?Go to Step 2.Turn O / D cut switch
OFF.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªO / D OFFº lamp come ON steadily?ªW / Bº circuit shorted
to ground.Go to Step 3.
3Check O / D cut Switch Circuit.
1) Check resistance between terminal E61-33
(G16 / J20 engines) or E61-14 (H25 engine) of
disconnected PCM connector and body ground with
O / D cut switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check O / D cut Switch for Operation.
1) Remove console box.
2) Disconnect O / D cut switch connector.
3) Check continuity between switch terminals under
each condition below.
Switch OFF position: No continuity
Switch ON position: Continuity
Is check result satisfactory?ªY / Rº circuit shorted
to ground.Replace O / D cut
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. O / D cut switch
4. P / N change switch
5. J / C
1. PCM
2. Fuse
3. O / D cut switch
4. P / N change switch
5. J / C
6. J / C
AUTOMATIC TRANSMISSION (4 A / T) 7B1-37
DIAGNOSTIC FLOW TABLE B-3 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT DOESN'T LIGHT AT IGNITION SWITCH ON BUT
ENGINE STARTS UP)
WIRING DIAGRAM
TROUBLESHOOTING
STEPACTIONYESNO
1ªPOWERº light circuit check:
(1) With ignition switch OFF, disconnect
couplers from PCM.
(2) Using service wire, connect E61-21 (G16 /
J20 engines) or E61-10 (H25 engine)
terminal of disconnected PCM coupler and
ground.
Does ªPOWERº light turn ON at ignition switch
ON?Poor E61-21 (G16 / J20
engines) or E61-10 (H25
engine) terminal
connection.
If OK, substitute a known-
good PCM and recheck.Bulb burned out or faulty
ªGr / Blº, ªB / Wº wire.

YH4
GRAND
VITARA
7B1-38 AUTOMATIC TRANSMISSION (4 A / T)
ª5º
ª4º
DIAGNOSTIC FLOW TABLE B-4 ªPOWERº LIGHT CIRCUIT CHECK
(ªPOWERº LIGHT COMES ON STEADILY)
WIRING DIAGRAM ± Refer to Table B-3 in this section.
TROUBLESHOOTING
STEPACTIONYESNO
1Check Power / Normal Change Switch Position.
Is switch button at Normal position?Go to Step 2.Set Power / Normal
change switch at
Normal position.
2Check Lamp Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Turn ignition switch ON.
Does ªPOWERº lamp come ON steadily?ªGr / Blº circuit
shorted to ground.Go to Step 3.
3Check Power / Normal Change Switch Circuit.
1) Check resistance between terminal E61-31
(G16/J20 engines) or E61-9 (H25 engine) of
disconnected PCM connector and body ground with
P / N change switch OFF.
Is continuity indicated?Go to Step 4.Check PCM ground
circuit for open.
If ground circuit is
OK, substitute a
known-good PCM
and recheck.
4Check Power / Normal Change Switch for Operation.
1) Remove Power / Normal change switch.
2) Check continuity between switch terminals ª4º and
ª5º under each condition below.
Normal position: No continuity
Power position: Continuity.
Is check result satisfactory?ªOr / Blº circuit
shorted to ground.Replace Power /
Normal change
switch.
Fig. for Step 1. Fig. for Step 4.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-39
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. Transmission range
sensor (switch)
1. PCM
2. Fuse
3. J / C
4. Transmission range
sensor (switch)
DTC P0705 (DTC NO.72) TRANSMISSION RANGE SENSOR (SWITCH) CIRCUIT
MALFUNCTION
WIRING DIAGRAM

YH4
GRAND
VITARA
G16/J20 Engines H25 Engine
G16/J20 Engines
H25 Engine
1. PCM
2. A / T input speed sensor 11 1 0
Bl / Y Bl / G16 8
Bl / Y Bl / G
7B1-42 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0715 (DTC NO.76) INPUT / TURBINE SPEED SENSOR CIRCUIT MALFUNCTION
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
Input speed sensor detected speed is lower than spec-
ification while vehicle running under all of the following
conditions:

at higher than 10 km / h (7 mph) with 1st gear in D
range for 1 sec. or more.

at higher than 20 km / h (13 mph) with 2nd gear in D
range for 2 sec. or more.

at higher than 30 km / h (20 mph) with 3rd gear in D
range for 2 sec. or more.
(2 driving cycles detection logic)
Input speed sensor and its circuit

PCM
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and turn O / D cut switch ON.
4) Shift select lever to D range and start vehicle.
5) Keep vehicle speed at higher than 10 km / h (7 mph) with 1st gear in D range for 2 sec. or more.
6) Increase vehicle speed and keep it at higher than 20 km / h (13 mph) with 2nd gear in D range for 2 sec. or more.
7) Increase vehicle speed and keep it at higher than 30 km / h (20 mph) with 3rd gear in D range for 2 sec. or more.
8) Stop vehicle.
9) Check DTC and / or pending DTC.

YH4
GRAND
VITARA
G16/J20 Engines H25 Engine
G16/J20 Engines
H25 Engine
1. PCM
2. A / T output speed sensor 23
22
WOr10 9
WOr
7B1-44 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0720 (DTC NO.75) OUTPUT SPEED SENSOR CIRCUIT MALFUNCTION
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA

With 4WD LOW switch OFF, no output speed sensor
signal is inputted while vehicle speed sensor signal
are inputted.
or

With 4WD LOW switch OFF, no output speed sensor
signal is inputted while engine running at higher than
specified engine speed with ªDº range.
(2 driving cycles detection logic)
A / T output speed sensor or its circuit

PCM
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and shift transfer lever to ª2Hº or ª4Hº range.
4) Drive vehicle at 40 km / h (25 mph) or more for longer than 10 sec. (or higher than 3500 rpm engine speed with
D range for longer than 10 sec.)
5) Stop vehicle and check DTC and / or pending DTC.

YH4
GRAND
VITARA
G16/J20 Engines H25 Engine
G16/J20 Engines
H25 Engine
1. PCM
2. Shift solenoid-A
3. Shift solenoid-B
4. TCC solenoid
AUTOMATIC TRANSMISSION (4 A / T) 7B1-47
DTC P0743 (DTC NO.65 / 66) TCC (LOCK-UP) SOLENOID ELECTRICAL
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
Voltage at terminal C51-1-8 for G16 / J20 (C51-1-2 for
H25) of PCM is high while TCC solenoid OFF is com-
manded or low while TCC solenoid ON is comman-
ded.
TCC (lock-up) solenoid valve

TCC (lock-up) solenoid valve circuit

PCM
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Shift selector lever in D range and keep it there for 10 seconds.
5) Increase vehicle speed to about 80 km / h (50 mph) in 4th gear and in D range.
6) Keep driving at above speed for 20 seconds.
7) Release accelerator pedal, decrease vehicle speed and stop vehicle.
8) Check DTC and / or pending DTC.